Posts Tagged purple

CiM colour testing: Aladdin and Boysenberry

Two purples here – both a similar colour but with different saturations. They’re both described by CiM as moonstones, so have a little bit of mistiness and aren’t entirely transparent.

Aladdin

15.03.22_CiMAladdin

15.03.22_Aladdin_spacers

The two spacers on the right are etched – you can see they didn’t etch well in the time I left them in, when it was fine for the opaques coming later. This wasn’t entirely surprising, as it tends to happen with moonstones and more transparent opalinos. In hand you can see more easily the slight mistiness of the moonstone.

15.03.22_AladdinGremlin_01

I made a gremlin – the body has a core of clear, so lightening it up a bit. This gremlin has been experimenting with cosmetics! I added some Gaffer purpur frit on the lips to prevent the teeth showing through, because this colour isn’t dark enough to block that.

15.03.22_StripedEgg

This egg has a stripe of Aladdin round the centre – that was a couple of wraps, allowed to melt down and spread. It’s a low saturation with a shadowy edge. (The other colours are caboose and chamomile – chamomile is yellower over the white, and something in the heating and rolling of the surface has made caboose misbehave somewhat with slight devit).

Boysenberry

15.03.22_CiMBoysenberry

The more saturated moonstone. I had a thicker rod of this, which may have had something to do with it, but I found this one pretty shocky and kept losing chunks when I was carefully rewarming it. It seems to lose heat relatively quickly too, so make sure you’re keeping your bead warm.

15.03.22_Boysenberry_spacers

Boysenberry again doesn’t etch well, and is really dark when used as spacers. You can still tell they’re purple rather than black, but only just. It’s a good berry colour.

15.03.22_BoysenberryGremlin_01

This gremlin again has a clear core, and you can see slightly that it lightens the body. No problem with being able to see through the lips here!

15.03.22_BoysenberryEgg

This egg is Effetre white with small and large dots of boysenberry, allowed to move with the heating and shaping. You can see the difference in saturation between the different dot types – the small ones have spread a lot more – and the white has formed separation lines between the dots.

Comparison

Here’s the two colours side-by-side, so you can see the difference in saturation.

15.03.22_AladdinBoysenberry_spacers

15.03.22_AladdinBoysenberry_Gremlins

, , , , , , , , , , , , , , , ,

Leave a comment

CiM colour testing: Ice Floe and Trapeze

The last two are a pair of pretty transparents.

Ice Floe

14.08.24_IceFloe

Ice Floe is a lovely pale icy blue. Gorgeous on its own in nuggets. The bead at the back has a base of Effetre clear, rolled in silver leaf and encased in Ice Floe – the silver’s definitely silver, so this could be a handy encasing colour to prevent it going gold. For the ribbed bead, I did a small core of Notos, which has lost most of the iridescence leaving a slightly aqua-tinged centre. Ice Floe did develop some trails of microbubbles in all these beads, but that’s less of a problem in a colour like this – they look watery not scummy. I don’t think I really noticed while making the beads, or I could have tried working it a little differently.

Trapeze

14.08.25_Trapeze

Trapeze is another dark lavender-alike… but this one looks and photographs as purple under halogens rather than blue! It does look *more* purple in sunlight, but it definitely colour-shifts far less than the others. So if that shift annoys you, this is a fab alternative. For the ribbed bead, I encased a base of Double Helix Psyche. That worked much better here than the last time I tried it!

14.08.25_Trapeze_Sunlight

So in sunlight it still has a lot more oomph… but if you weren’t looking at the two pics side-by-side like this, the above one still gives a better impression of the purple than the baby blue you get with dark lavender.

, , , , , , , , , , , , , , , , , ,

Leave a comment

CiM colour testing: Whisper, Primrose, Coronation Day, Bubblebath

Whisper

14.08.24_WhisperGremlin_01

This gremlin is made of Whisper, which I liked better than I thought I would! It stays far more opaque than expected – again, the body is over clear and has a bit more misty translucence, but the lips are opaque enough not to let the teeth show through (which is good as it can look kinda scary!). This is rather like Frangipani, but a bit less pink, I think. Like a very diluted one of the plum uniques. It gets the same slight webbing on the surface as you work it.

This rod of Whisper was pretty shocky – I had to baby it back into the flame to stop it shocking off above where I had been working, and when adding the upper lip I must have got the flame too close to a cooler section, as it shocked right off, leaving me with a half-applied lip ending in a centimetre of rod.

14.08.24_WhisperGremlin_02

In hand to make it stand out a bit better from the background.

Primrose

14.08.24_PrimroseGremlin_01

Primrose is a rather pretty pink (but primroses are yellow!). This rod was really shocky though – worse than Whisper – and it would crack about an inch above the end every time I took it out of the flame and put it down, so when I next had to use it, I needed to not only bring it back slowly high up in the flame, but make sure I got that whole bottom inch heated up before using it. Again, it cracked off while doing the top lip. The actual colour is really nice, and the glass is fine to work with once molten, but you do need to be careful. I imagine using this for one-at-a-time dots would strain one’s patience.

I don’t know if this will be the case with all rods of Primrose or if this was a particularly nasty one, but for a rod without airbubbles running through it this was pretty bad (those just tend to explode in all directions). I was using it alongside a thick Effetre clear rod for the cores, which can have a tendency to crack at the end when cooling just because it’s bigger, hence needing to go back in carefully enough to melt those cracks (but they do heal quickly again). That was far less hassle to use than the Primrose. I don’t even know if keeping the end preheated would help, because it might just shock above that.

A lot of rods do the “crack a bit when you put them down” thing, but usually it’s just at the tip and there’s no real problem. What was unusual here was how far down it cracked, which is what made it harder to use. I use a rod rest, so wasn’t putting it down on a surface either.

Coronation Day

14.08.25_CoronationDayGremlin_01

Coronation Day is a dark opal purple. I like this one – nice to use, pretty colour. It’s very like some of the darker plum uniques, again, but I’d need to put them side by side to check differences. You may be able to see here – the feet and bottom lip have opacified and lightened more, while the top stayed darker and more translucent. This is the same thing a lot of the CiM opals do, and depends on how much heating and cooling they get after the last time they were molten (and mayybe on kiln position too). I added the little yellow flowers on the head after doing the feet, but didn’t melt the head while doing that.

Bubblebath

14.08.25_BubblebathGremlin_01

Bubblebath is a similar shade to Whisper in a pale rose quartz kind of way, but far more translucent. The body over clear is very transparent, and I didn’t even try using it for the lips and eyelid, so those are Coronation Day again. I should do some transparent styles of bead with this – could be interesting encasing something shiny, and should make lovely nuggets on its own.

14.08.25_BubblebathGremlin_02

Another look.

, , , , , , , , , , , , , , ,

Leave a comment

Nail art: Neon Psychedelia marble decals

Bright!

These are so very much not colours that I’d normally wear, but I thought I’d go ahead and see if they grew on me.

These were the marble pattern made from the Models Own colours – Luis Lemon, Pukka Purple and Dinky Pinky. I prefer the yellow when it isn’t on top of the blue, because of course it picks up a green tinge then.

14.01.18_NeonPsychedelia_01

My favourite is absolutely my pinky nail. I like the colours there and the accidental little heart!

I put the decals on over a base colour of the yellow and then Seche Vite topcoat. This decals was rather thick in places, which causes problems at the base of the nail particularly as you get a very noticeable ridge there and this is where any catching of the polish will happen. This is also why my pinkies were my favourites, as they came from a thinner section. I had to rescue a couple of these and reattach them (and of course, adding a second topcoat makes the problem worse). They lasted 6 days before I took them all off, which isn’t bad. These decals were again made on the 30th Dec, and put on on the 19th Jan. It *was* getting brittle by this point. I ended up with quite a few little broken off pieces, which you can use as a confetti decoration placing just a couple over a base colour – it looks a little different that way.

14.01.18_NeonPsychedelia_02

14.01.18_NeonPsychedelia_03

I did try going round the edges with acetone to melt them down slightly, but that’s a mistake when the backing isn’t clear because the purple especially gets smeared out and muddy along the edges if you do that. Never mind!

I took all the rest of my decals off their backing sheets when I was getting these ready. I got a surprise as the very first one I made, with greens and metallic brown, came straight off the greaseproof paper no problem! The rest were more finicky and more brittle. (They’ve all been together in a ziplock bag). It had the Collection 2000 clear down first, which none of the others did, and then W7 spearmint. So something in that combo made it very easy to remove – possibly just leaving it so long, as the clear was very hard to remove earlier on its own.

, , , , , , , , , , , , ,

Leave a comment

A-dabbling in nail art – marbled decals

I asked for (and received!) vast quantities of new nail polishes for Christmas, since I’ve started having a go at doing nail art again. I did a little bit of multi-colour and attempted patterns some years ago, but nothing like what people are doing now!

I like nail art because it’s a small decorative thing that is pretty much entirely for my benefit – I spend a lot of time at a computer, so looking down and being able to admire interestingly-coloured nails makes me happy. Also, it stops me biting my nails :p

There are so many nail art blogs out there now doing amazing things – I’m only just seeing what is possible.

So, just before New Year, I’d read this tutorial: Dry Water Marble Nails Tutorial on Nuthin’ But A Nail Thing’s blog. I have always loved marbled paper and this looked a lot of fun. I like the idea of making decals with nail polish that you then apply later, because that avoids having to paint left-handedly when I’m right handed.

I did mine on greaseproof paper, because another blog had mentioned parchment paper being the easiest surface to get the polish off. (I think what the US calls parchment paper we call greaseproof, but no idea if theirs is thicker). Well, it will depend on the polishes, but greaseproof paper didn’t work *that* well for me – the polish comes off, but it grips quite tightly and it’s tricky to get the edges up without stretching or tearing, and greaseproof paper is very thin, so also easy to tear with tweezers. Next time I will try on ziplock bags – someone else used a sheet of acetate.

Here are the marbled decals I made, anyway!

13.12.30_MarbledNailDecals_01

The top green and brown one was the first – I made my initial blobs a bit small on that one. I think the next two look a lot better. The neon one uses Models Own Luis Lemon (really neon yellow!), Pukka Purple and Dinky Pinky.

The glittery lime and brown one uses W7 Mojito and Collection 2000 maxiflex Mocha and Shiraz. I was impressed that the mojito works as dots on top of the others – it sits perfectly well on top of them and shows up as itself. Since it’s a transparent with green glitter, I wasn’t sure if it would stay dense or not.

13.12.30_MarbledNailDecals_02

I was really pleased with the orange one! It made such smooth dots that I didn’t marble it at all since it looked great as was. It is Topshop’s Venus Fly Trap (the lime), Stage Dive (the orange) and Pillar Box (red). Many thanks to my boyfriend for venturing into Topshop to get those! I didn’t even know they did a range of nail stuff, not been in there in years.

I was in two minds about the purple one – the colours bled a lot so you didn’t get clear edges, so I did fairly extreme marbling by dragging lines in all directions to get something that wasn’t too muddy. I tried using that one first, and it works really well! It was Revlon Chroma Chameleon Aquamarine, which is a colour-shifting blue to light purple metallic polish, plus Jess Moonflower and Breathless. Moonflower is a midnight blue satiny colour, and Breathless is a blue-pinky holographic. Looks bluish in the bottle, made all the pink glitter in the decal.

I decided to name this combo Midnight Garden because there are some decidedly foliage-like sections.

13.12.30_MarbledNailDecals_NightGarden_01

13.12.30_MarbledNailDecals_NightGarden_02

I did three nails per hand, over Collection 2000 Hot Looks Button Moon, which is a pale wintry blue. ‘Scuse edges, etc etc. Not quite at the professional finish stage yet!

The other nails are two layers of the aquamarine with one layer of Miss Sporty Sparkle Touch 889, which is apparently called Amethyst Dust – no name on bottle. Small pink, blue, red, silver and amethyst glitter. One layer is just a little bit of glitter. That’s what I had on before, so just left it on those nails as the base colour was the same.

I don’t have any fancy top or base coats as yet, so have just been using Collection 2000’s maxiflex clear. Being flexible, it’s easily dented and doesn’t stay quite as shiny as I would like.

Also, after a few days I had the rather disconcerting experience of having all layers of polish on my first finger fall off together! Look down, no polish at all on that nail anymore. I think I much have caught an edge on something and then the whole thing just came straight off, but without enough of a tug for me to notice as it happened. I tried putting one back on and it’s staying there as well as the others for the time being…

I’m keeping the rest of the decals sealed in a ziplock bag, so they hopefully won’t get too brittle.

, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,

1 Comment

52 earrings: #37 Magic Can Swing

A pair with a lot of motion this week!

#37 Magic Can Swing

13.09.11_E36_MagicCanSwing_01

These have a pair of my lampwork beads in a striking silver glass that goes all shades of blue, purple, and a bit of green. They are wire-wrapped in sterling silver and swing and dangle about freely.

13.09.11_E36_MagicCanSwing_02

52 little things links
Craft Pimp Week 36 thread
• Linda of Earthshine Lampwork Bead and Jewellery Design: http://www.earth-shine.co.uk/
• Sue of BlueBoxStudio: http://www.blue-box-studio.blogspot.co.uk
• Jolene of Kitzbitz Art Glass: http://kitzbitzartglass.blogspot.co.uk

, , , , , , , , , , , , ,

Leave a comment

52 earrings: #28 Spiral Hoops

Some spiral kumihimo loops with lampwork beads on them this week.

#28 Spiral Hoops

13.07.07_E28_SpiralHoops_01

The kumihimo spiral braids are in purple, teal green, gold and baby blue. These are the ones with the looser spiral – if you make them the other way you get a tighter spiral. I added a pair of big hole beads in dark turquoise I made previously. (I also had some in Lauscha turquoise which doesn’t have the grey sheen, but they were a little too bright, I thought). Copper earwires.

13.07.07_E28_SpiralHoops_02

52 little things links
Craft Pimp Week 27 thread
• Linda of Earthshine Lampwork Bead and Jewellery Design: http://www.earth-shine.co.uk/
• Sue of BlueBoxStudio: http://www.blue-box-studio.blogspot.co.uk
• Jolene of Kitzbitz Art Glass: http://kitzbitzartglass.blogspot.co.uk

, , , , , , , , , , , , , , , , ,

Leave a comment

%d bloggers like this: